Free to browse

Tips & how-to guides

1,874 free skill tips with unique step photos — plus long-form guides with FAQ and trusted sources. Every tip links to a full photographed course.

Browse tips

💻 Tech & Internet · Step 6/6

Same SSID, wired backhaul if you can

Same SSID, wired backhaul if you can — step 6 of 6 in Home Wi-Fi That Reaches the Bedroom. Put a node in the hallway toward the dead room, not inside the dead room as the only hop through three walls.

From course: Home Wi-Fi That Reaches the Bedroom

🏠 Home & DIY · Step 1/8

Run the stud finder — or use a magnet

Run the stud finder — or use a magnet — step 1 of 8 in Hang a Picture Without Cracking the Wall. Turn on the stud finder, calibrate on a blank area, slide horizontally. It beeps or lights at the stud edge.

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 2/8

Choose the right anchor for the weight

Choose the right anchor for the weight — step 2 of 8 in Hang a Picture Without Cracking the Wall. Weigh the frame (bathroom scale works — weigh yourself, then hold the frame and subtract).

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 3/8

Gallery height: center of art at 145 cm from floor

Gallery height: center of art at 145 cm from floor — step 3 of 8 in Hang a Picture Without Cracking the Wall. This is the museum standard — the center of the artwork at 57 inches (145 cm) from the floor.

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 4/8

Mark with painter's tape and a pencil

Mark with painter's tape and a pencil — step 4 of 8 in Hang a Picture Without Cracking the Wall. Put a small piece of painter's tape at your calculated nail point. Mark the center with a pencil on the tape.

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 5/8

Stud: drill pilot, drive screw, leave 5 mm proud

Stud: drill pilot, drive screw, leave 5 mm proud — step 5 of 8 in Hang a Picture Without Cracking the Wall. If you hit a stud: drill a pilot hole slightly smaller than the screw. Drive the screw until 5 mm of the shaft is still exposed — that is…

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 6/8

Hang, level, and step back

Hang, level, and step back — step 6 of 8 in Hang a Picture Without Cracking the Wall. Hook the wire over the screw or slip the D-rings over both screws. Place the level on top of the frame. Adjust until the bubble centers.

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 7/8

If the wall cracked or the anchor pulled: patch first

If the wall cracked or the anchor pulled: patch first — step 7 of 8 in Hang a Picture Without Cracking the Wall. Fill the damaged hole with spackle, let it dry, sand flush, then touch up with matching paint.

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 8/8

Pass criteria: level, secure, no damage

Pass criteria: level, secure, no damage — step 8 of 8 in Hang a Picture Without Cracking the Wall. You pass when the picture is at the intended height (center at roughly 145 cm from floor), level (bubble centered), and the fastener holds…

From course: Hang a Picture Without Cracking the Wall

🏠 Home & DIY · Step 1/6

A real level line

A real level line — step 1 of 6 in Floating Shelf Install. Typical desk shelf sits 25–30 cm above the work surface. Pencil a line longer than the shelf. Laser or a long level.

From course: Floating Shelf Install

🏠 Home & DIY · Step 2/6

Two studs minimum

Two studs minimum — step 2 of 6 in Floating Shelf Install. A 90 cm shelf should hit two studs. If it can't, shorten the shelf or add a third support.

From course: Floating Shelf Install

🏠 Home & DIY · Step 3/6

Pilots and the first bracket

Pilots and the first bracket — step 3 of 6 in Floating Shelf Install. Pilot into stud center. Depth = screw length minus a bit. Vacuum dust so screws bite wood.

From course: Floating Shelf Install

🏠 Home & DIY · Step 4/6

Toggles if you must

Toggles if you must — step 4 of 6 in Floating Shelf Install. Snaptoggle-style, hole size exactly as packed. Cheap plastic expansion anchors are not for books. Mix stud + toggle if you have to.

From course: Floating Shelf Install

🏠 Home & DIY · Step 5/6

Dry fit and the tiny Allen screw

Dry fit and the tiny Allen screw — step 5 of 6 in Floating Shelf Install. Slide the shelf. If it binds, don't hammer the face. Alignment is off. Many kits have a set screw underneath — snug it so the shelf cannot…

From course: Floating Shelf Install

🏠 Home & DIY · Step 6/6

Unload and inspect

Unload and inspect — step 6 of 6 in Floating Shelf Install. If you see a new crack from a bracket, take the books off. The fastener pulled or missed wood. Redo into a stud.

From course: Floating Shelf Install

☕ Coffee & Drinks · Step 1/4

Rinse the filter

Rinse the filter — step 1 of 4 in Pour-Over Coffee. Put the paper in the cone. Pour hot water through it into the server, then dump that water.

From course: Pour-Over Coffee

☕ Coffee & Drinks · Step 2/4

60 g water on the grounds

60 g water on the grounds — step 2 of 4 in Pour-Over Coffee. Start timer. Pour 60 g water, just enough to wet all the grounds. Wait 45 seconds. The bed should rise and bubble if the coffee is fresh.

From course: Pour-Over Coffee

☕ Coffee & Drinks · Step 3/4

Two circles to the line

Two circles to the line — step 3 of 4 in Pour-Over Coffee. Pour to 300 g by 1:15, slow spirals, keep the bed wet. Then to 500 g by ~1:45. Let it draw down. Total time ~2:45–3:30 is a good window.

From course: Pour-Over Coffee

☕ Coffee & Drinks · Step 4/4

Swirl the server

Swirl the server — step 4 of 4 in Pour-Over Coffee. Swirl, share, taste. If it's tea-like and sour, finer next time. If it's heavy and bitter, coarser.

From course: Pour-Over Coffee

☕ Coffee & Drinks · Step 1/4

30 g, sea-salt size

30 g, sea-salt size — step 1 of 4 in French Press That Isn't Gritty. Weigh 30 g. Grind coarse — distinct particles, not dust. If you only have a blade grinder, pulse and shake; accept some grit or buy a $30…

From course: French Press That Isn't Gritty

☕ Coffee & Drinks · Step 2/4

60 g to bloom 30 seconds, then to 500 g

60 g to bloom 30 seconds, then to 500 g — step 2 of 4 in French Press That Isn't Gritty. Coffee in. Start timer. Pour 60 g, stir so there are no dry pockets. At 0:30, fill to 500 g.

From course: French Press That Isn't Gritty

☕ Coffee & Drinks · Step 3/4

At 4:00 stir the crust, skim if you want, plunge 15–20 seconds

At 4:00 stir the crust, skim if you want, plunge 15–20 seconds — step 3 of 4 in French Press That Isn't Gritty. A spoon through the crust. Optional: skim foam and floaters. Plunge straight down slowly.

From course: French Press That Isn't Gritty

☕ Coffee & Drinks · Step 4/4

Into a mug or pitcher now

Into a mug or pitcher now — step 4 of 4 in French Press That Isn't Gritty. Leave the last swallow of sludge in the press. Drink. If it's bitter and thick, coarser tomorrow. If it's thin and sour, finer or longer.

From course: French Press That Isn't Gritty

🐾 Pets · Step 1/4

One per cat plus one

One per cat plus one — step 1 of 4 in Cat Litter & Scratching. Quiet corners, different rooms if you can. Scoop daily, full change on a schedule. Don't hide it beside their food.

From course: Cat Litter & Scratching